Home » Tekken Tag Tournament » Tekken Tag Tournament – Arcade Manual – English

Tekken Tag Tournament – Arcade Manual – English

Details

Type: Manual
Platform: Arcade
Language: English
Size: 1.09 MB
Filename: tekken-tag-tournament_arcade_manual_en_uc2.pdf

View manual text

INTRODUCTION
Thank you very much for purchasing TEKKEN TAG TOURNAMENT PC BOARD KIT (hereafter called
“this product”).
This operation manual explains the following:
l

Installing and connecting this product to a general-purpose game cabinet (hereafter called
“cabinet”) safely,

0 Adjusting this product for operation safely,
0 Operating this product safely,
.
.
+-VT
l

Dismounting, safekeeping, and transporting this product safely,

Disposing this product safely,

0 Making full use of the efficiency of this product to operate it right.
Reference for this product and/or for repair:
Contact your distributor to make inquiries about this product and/or about repair.

1. SAFETY PRECAUTIONS - Be sure to read this part for safe use To the owner:
0 When the owner of this product entrusts the other person(s) to install this product on the cabinet, to
connect, to adjust for operation, to operate, to inspect, to clean, to troubleshoot, to disassemble. to
keep, to transport and to dispose, direct such a person(s) to read the applicable part of this manual
before conducting the task and to observe the instructions.
0

When reselling this product, always attach this operation manual to the PC Board.

l-l Level of Danger
In this operation manual, the matters that require attention are classified as follows according to the
level of the danger:
!
WARNING: _ Players and/or technicians can be killed or seriously injured if such
A
danger cannot be avoided.
!
CAUTION:
A

Players and/or technicians can be slightly injured if such danger
cannot be avoided.

T’he matters that require attention not concerning safety but functions shall be indicated with the
mark below.
w : The notices concerning the functions and protection of the product.

l-2

Readers of t@s operation manual
This operation manual is written for staff of a location operating amusement game machines. But
the part noted with “To be serviced by a qualified service technician only” on the Table of Contents
and on the title of each chapter is written especially for a qualified service technician. Such a task
should be conducted only by a qualitied service technician who would fit the following
requirements.

A qualified service tekhnician :

* A person who works for designing, manufacturing, inspecting, and maintenance servicing at an
amusement machine (AM) manufacturer, and a person who has technical knowledge of electrical
engineering, electronics, and mechanical engineering equivalent to a graduate of a technical high
school or more, and conducts maintenance services (repair) of an AM equipment on a daily basis.

-l-

1-3 Safety Precautions
1-3-1 General Safety Precautions

7 A WARN’NG

0 Do not dismount nor modify this product. DO flat conduct any works not described in this operation
manual. Otherwise an electrical shock or fire may occur.
0 This product is designed for indoor use only. Do not install, connect, or operate this product
outdoors. It may cause a fire or electrical shock.
0 Be sure to use the replacement parts specified by Namco Ltd. Using substitute parts may cause a fire
or electrical shock. Contact your distributor to order parts. The replacement parts are listed under
“11. Replacement Parts List” on p.56.

Do not perform any works with wet hands. Otherwise it may cause an electrical shock.

0 Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet before
conducting any works such as installation and connection (except transferring the data to be displayed
on the Namco-made CYBERLEAD cabinet), inspection, cleaning, troubleshooting, disassembling.
Otherwise an electrical shock may happen.

l-3-2

Safety Precautions When Installing and Connecting

-..

! WARNING :

When connecting to the cabinet corresponding to JAMMA

standard:

0 The power source on the cabinet connected to the JAMMA edge connector should fit the following
requirements:
- Voltage allowable error for +5V should be +5%, Amperage should be 2SA or more
- Voltage allowable error for +lZV should be ti%, Amperage should be 2A or more
If the power source does not conform to this requirement, it may cause a fire.

When c?nnecting

to the cabinet corresponding to JAMMA

VIDEO standard (JVS):

0 The power source on the cabinet connected to the power cable should fit the following requirements:
- Voltage allowable error for +5V should be G%, Amperage should be 2.5A or more
If the power source does not conform to this requirement, it may cause a fire.

--7-

l-3-3

Safety Precautions When Operating

I
A WARNING :
-.

0 Should any off-flavor or noise occur, turn OFF the power switch of the cabinet immediately and stop
operation. Then unplug the power cord from an electrical outlet and contact your distributor. If the
machine is kept operating without solving the trouble, it may cause an electrical shock or fire.
0 Make sure that installing and connecting were conducted in accordance with the instructions and the
procedure specified in this operation manual (Ref. “5. INSTALLING AND CONNECTING” on p-9)
before operation. If it is not installed and connected correctly, it may cause a fire, electrical shock or
machine trouble.

l-3-4

Safety Precautions When Disposing

0 Do not throw this product into a fire. A lithium battery used in this product may blow to cause injury.
0 When disposing this product, collect, transport, and scrap it in accordance with law and orders.
0 If entrusting others to collect. transport, and scrap this product, hire specialists in each of such work.

-3-

TABLE OF CONTENTS
INTORDUCTION
1.

SAFETY PRECAUTIONS - Be sure to read this part for safe use - ....................................................

l-1 Level ofDanger ..............................................................................................................................

1-2 Readers of this operation manual ....................................................................................................

l-3

Safety

Precautions...........................................................................................................................

1-3-1 General Safety Precautions.. .................................................................................................

2
2

l-3-2 Safety Precautions When Installing and Connecting.. ..........................................................

l-3-3 Safety Precautions When Operating .....................................................................................

l-3-4 Safety Precautions When Disposing.. ...................................................................................

TABLE OF CONTENTS ._.............................................................................................................................

SPECIFICATIONS . . . . . . . . . . . . . . . . .._..............................................................................................................

CHECK OF PACKAGE . . . . .._..................................................................................................................

4. COMPONENTS . .._....._..........................................................................................................................,.
5.

INSTALLING AND CONNECTING -To be serviced by a qualified service technician only L.. ......
5-l

Before Installing (Both for m, m) ..........................................................................................

5-2 Installing the PC Board on the Install Board of the Cabinet
(Both for m, m) .......................................................................................................................
5-3 Connecting to the Cabinets Corresponding to the JAMMA Standard

5-3-2 Checking the Extended Edge Connector m .....................................................................

m ..................................................................................

5-3-4 Connecting to the Speaker m ...........................................................................................

5-3-5 Connecting t o the connectors

m ......................................................................................

Connecting the Product to the Cabinet Corresponding to JAMMA VIDEO Standard (JVS)
ma ................................................................................................................................................
5-4-l Connecting to the Control Panel
5 4 2 Connection of Cables

11
13

5-3-3 Connecting to the Control Panel

5-5

9
10

m ......................................................................

5-3-l Checking the JAh4MA Edge Connector

5-4

m .................................

m ...............................................................................

m ................................................................................................

Pasting the Stickers (Both for m, m) ......................................................................................

20
20
21
23

ADJUSTMENT FOR OPERATION ......................................................................................................

6-1 The Basic Knowledge of the Adjustment .......................................................................................

6-l-l Adjustment Switches, Knobs ................................................................................................

6-l -2 Selecting the Adjusting Items ...............................................................................................

26
28

6-l-3 Finishing the Test Mode .......................................................................................................

-4-

28
6-2 Display Test (Check/adjustment of the display) .............................................................................
_79
6-2-l Common Operation ..............................................................................................................
6-2-2 CONVERGENCE (Checking/adjusting the size, position, aspect ratio, distortion of the
30
picture) ..................................................................................................................................
6-2-3 COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of the picture
signal outputted by the PC board) ........................................................................................
32
6-3 SWITCH TEST.. .............................................................................................................................
34
35
6-4 SOUND TEST (Test/setting of the sound) .....................................................................................
6-5 JVS CABINET OPTIONS (Setting VIDEO SYNC on the cabinet corresponding to the
36
JAMMA VIDEO standard (JVS)) m .......................................................................................
38
6-6 GAME OPTIONS (Setting of the game options) ...........................................................................
40
6-7 COIN OPTIONS (Setting of play fees) ..........................................................................................
42
6-8 A.D.S. (Checking the d a t a on playing results in the past) ..............................................................
42
6-9 DATA CLEAR (Clearing various data, initializing to default settings) .........................................
45
45
45
46

OPERATION ..........................................................................................................................................
7- 1 Persons Not Recommended to Play ................................................................................................
7-2 Restrictions When Operated ...........................................................................................................
7-3 How to Play .....................................................................................................................................
INSPECTION & CLEANING, TROUBLESHOOT-ING
-To be serviced by a qualified service technician only - ................................................
8-l Inspection & Cleaning ....................................................................................................................
8-2 Troubleshooting ..............................................................................................................................

. ....................

Disassembling, Safekeeping, Transportation ..........................................................................................
9-1 Disassembling -To be serviced by a qualified service technician only -. .....................................
9-2 Safekeeping .......... . ..........................................................................................................................
9-3 Transportation .................................................................................................................................
10. DISPOSAL _..__............__...........................................................................................................................
11. ’ APPENDIX A.
-Control Panel Layout
-Electrical
Diagram

............................................................................................

_ ................

47
47
48
50
50
52
52
53
54

The chapters marked m are indispensable for installing this product to the cabinets corresponding to the
JAMMA standard.
The chapters marked m are indispensable for installing this product to the cabinets corresponding to the
JAMMA VIDEO standard (JVS).
-5-

2. SPECIFICATIONS
Description

Item

Corresponding Standard

JAMMA standard * 1
JAMMA VIDEO standard (JVS) *2

1 Dimension

(268mm x 230mm x 30mm

Weight

58Og

Input power source

[Connected to JAMMA
standard terminal ]
+5V 55% (2SA or more) and +12V ?5% (2.0.4 or more)
[Connected to JAMMA VIDEO standard (JVS) renninal]
+5V 55% (2.5A or more)

Restriction

Indoor use only
Temperature : 0°C - 50°C.

Cabinets applicable to connect

Cabinets
corresponding to JAMMA standard
Cabinets corresponding to JAMMA VIDEO standard (JVS)

Direction of the monitor
and the monitor signal

Direction of the monitor : Sideways
Type of scanning retrace line : non-interlace
Synchronizing signal : Switchable to composite I separate *3
Horizontal synchronizing frequency : 15.7.5kI-I~
Vertical synchronizing frequency : 60.OHz

Networked game play

Available only with the cabinets corresponding to JAMMA VIDEO standard
(JVS). (Install fwo cabinets linked with cables. Need one PC board only.)

Control panel

[Pair control panel (10 be used for 2P play in one cabinet)]
g-direction
joystick
1x2
Button switch
5x2
Start switch
1x2
[Single control panel (to be used for networked play by connecting two cabinets
with cables)]
Each cabinet should have:
g-direction
joystick I
B u t t o n swirch
5
Start switch
1

1 How to install it on cabinets

1Fix to the wooden install board of the cabinet

Humidity : 10% - 85% (no condensation)

JAMMA standard (JAMMA STANDARD: abbreviated as IS)
Standards on the edge cdnnectors for video game machine PC boards provided by Japan Amusement
Maihine Manufacturers Association (JAMMA) in 1986

JAMMA VIDEO standard (JAMMA VIDEO STANDARD; abbreviated as JVS)
Standards on connection between video game machine PC boards and other support devices provided
newly by Japan Amusement Machine Manufacturers Association (JAMMA) in 1996

Effective only when installing it on the cabinets corresponding to JAMMA VIDEO standard (JVS)

-6-

3. CHECK OF PACKAGE
This product includes the following items:

PRE-KIT A, TEKKEN TAG TOURNAMENT
Part No.

No.
1
2
3
4
5
6
7
8
9
IO
11
12
13

Qty.

Description

TM-08898-00
Assv. Buttons and Joystick
TT40-0888500
De&, Side Panel, Left
TT40-0888501
Decal, Side Panel, Right
lT40-08887-00 Decal, “TAG”
TT40-08888-00
Decal, Marquee
TT40-08889-00
Decal, Control Panel
lT40-08890-00
Decal, “PUNCH”
lT40-08891-00
Decal, “KICK”
lT40-08892-00
Decal, “PLAYER 1”
lT40-08893-00
Decal, “PLAYER 2”
lT40-08894-00
Decal, Tekken Tag Tourn. Logo
lT40-08899-00
Poster, Game Promo
lT50-08897-00
Harness, JAMMA 56 pin w/tag
Includes 48 pin JAMMA

TT95-08896-00
14
i5
VG05-06607-00
16 VG40-08751-00
17 VG44-07943-00
18 VG46-02653-00
19 VG78-05265-00

Cover, Control Panel
Mounting Feet, PCB w/screws
Poster, AAMA ratings
Label, Epileptic Warning
Label, FCC
Assy, Housing and Ferrite Bead

i?
2
2

2
1

1 bag of 4
1
2

PRE-KIT B, TEKJSEN TAG TOURNAMENT
Part No.

No.
1
2
3
4

Qf-Y.

Description

TTO3-08884-00
PCB Kit, Tekken Tag Tournament
lT40-08886-00 Card, Game Instructions
TT40-08910-00
Card, Move List
TT450889500 Manual, Game Kit

1
1

*NOTES:
l
l

Be sure to check that all items are included.
If there is something missing, contact your distributor.
Save the packing materials in case of storage and transportation of this product.

Refer to chapter “Il. REPLACEMENT PARTS LIST” on p. 54 for the service parts.
-7-

4. COMPONENTS
Option switch

Parts mounted side

Terminal for the J

Terminal for the extende
edge connector
Speaker volume

cabinet corresponding to
JAMMA VIDEO standard (JVS)
(Ref. p.22 for details)

PC Board

Wire

Extended edge

preventive key

Extended Edge Harness

-8-

5. INSTALLING AND CONNECTING
-To be serviced bv a aualified service technician onlv -

! WARNING.:

Always turn off the power switch of the cabinet and unplug the power cord from an electrical outlet
before conducting any work, except the work for “5-4-3 Transferring the data to be displayed on the
Namco-made CYBERLEAD cabinet”. Otherwise an electrical shock may occur.

0 This product is designed for indoor use only. Do not install and connect this product outdoors. It may
cause a fire or electrical shock.

m 0

A service technician should not be charged electricity when installing and connecting the
product. Static electricity may cause this product breakdown or damage.

l Do not attempt to perform conductivity test using a multi-meter. Even an internal voltage
of a multi-meter may damage the IC of the PC board.
This product is available for either cabinet, the one corresponding to JAMMA standard, or the one
corresponding to JAMMA VIDEO standard (JVS), however, connecting procedure is different each other.
*

Check if your cabinet is applicable to this product referring to “2. SPECIFICATIONS” on p.6.

Chapters in this operation manual corresponding to each standard
Check the standard of your cabinet, and read the following chapters in accordance with that standard.
0 Connecting to the cabinet corresponding to JAMMA standard:
Read the chapters “Both for m, m” on pages 10 - 12,23, and the chapters “for m” on pages 13 19.
l

Connecting to the cabinet corresponding to JAMMA VIDEO standard (JVS):
Read the chapters “Both for m, m” on pages 10 - 12.23, and the chapters “for m” on pages 20 22.

Cabinet
Namco-made CYBERLEAD cabinet, for example
-9-

5-1

Before Installing (Both for m, m)
You prepare the necessary

items

to install this product as follows.

Items needed
Operation
(+)

manual

attached

your

cabinet

Remarks
Check

the

handling

your

Reference
cabinet.

Countersunk head tapping screw (4 pieces)
Fix the lesslocks
on the install board of
Diameter: one size smaller than the diameter of
your cabinet. You may use the furnished
installation hole on the side of lesslocks
which ones with your cabinet.
fix lesslocks
on the install board.
Length: Long enough to fix the lesslocks
on the install
board but not too long to stick through the
install board

Lesslock
(4 pieces)
Those which have holes to be installed on the install
board and holes to install the PC board

Chapter 5-2 pfi.m
(page 12)

Keep space between the install board and
the PC board. You may use the furnished
ones with your cabinet.

Chapter 5-2 m,m
(page 12)

Pan head machine screw (4 pieces)
Fix the PC board into the lesslocks.
You
Diameter: appropriate size for the PC board installation
may use the furnished ones with your
cabinet.
hole (or internal thread) of the lesslock.
Length: Not trm long to stick through the lesslock
when the PC board is fixed. or not too short to
tix it on the lesslock
You can adjust the
length by using tk spacer mentioned below in
cases the screws are too long.

Chapter 5-2 I,=
(page 12)

Spacer (4 pieces)
Minor diameter.
;;i;e&te
Length:
Solder

size for the screws mentioned

appropriate sire to adjust the length of the
screws above.
caulking,

Connect wires to micro switches. Please
read the referential chapters to check if
they are necessary or not.

Chapter 5-3-l m
(page 13),
chapter 5-3-3 m
(page 16).
Chapter 5-34 m
(page 17)

Insulating heat contraction tube and a drier for heat
:ontraction
tube

Insulate the connection parts of the wires.
Please read the referential chapters to
check whether they are necessary or not.

Chapter 5-3-l m
(page 13).
Chapter 5-3-3 m
(page 16)

nsulating

Insulate the edge of unnecessary wires
and connecton. Not necessary when
connecting to the cabinet corresponding
to JAMMA standard with 2
speakerS(sterea
specification).

Chapter 5-34
(page 17).
Chapter 54-2
(page 21)

tape

crimp-style

terminal

Adjust the length of the pan head machine Chapter 5-2 m.m
screws when installing the PC board on
(page 12) -.,
the lesslocks. Not necessary unless the
pan head machine screws are too long.
You may use the furnished ones with your
cabinet.

-lO-

a
m

Installing the PC Board on the Install Board of the Cabinet
(Both for m, m>
First install the PC board on the install board according to the following procedure.
1

Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Read the part on “Installation of the PC board” of the operation manual of your cabinet, and
open the door of the PC board stooge and take out the PC board install board.
When setting networked head-to-head play by using two cabinets corresponding to JAMMA
VIDEO(JVS), you can use either cabinet.

Instal! board

Namco-made CYBERLEAD cabinet, for example

In cases other PC boards are connected, remove them in accordance with the procedure
described in the operation manual of your cabinet.

-II-

Install the PC board at the center of the install board with the countersunk head tapping screws,
lesslocks, spacers (unnecessary if the pan head machine screws are not too long) and pan head
machine screws, through the four install holes on the PC board.

208.6mm

Lesslock(4

pieces)’

Q 3.6mm 4 points ’
Spacer (4 pieces)

screw (4 pieces)

(+) Countersunk head tapping screw (4 pieces)

m 0 Do not use a metal install plate but a wooden board for installation of the PC board.
Otherwise it may be short-circuited and damaged.
l Be sure to use pan head machine screws to install the PC board on lesslocks. Using
countersunk head screws when spacers are not needed may break the install holes
on the PC board.
0

Clean the cabinet with cleaners if it is dirty with dust.

5-3

Connecting to the Cabinets Corresponding to the JAMMA Standard

5-3-l

Checking the JAMMA Edge Connector !H
Use the JAMMA edge connector attached to the cabinet to connect this product to the cabinet
corresponding to the JAMMA standard.
1

Check if the terminal numbers of the JAMMA edge connector of the cabinet conform to the
table of JAMMA edge connectors below. If not, connect wires to that part by soldering or
fixing applicable crimp-style terminals.

w l Apply insulating heat contraction tube on the connecting part to prevent shortcircuit.
l

r
I

- Nothing should be connectedto the blank part of the table below. Otherwise the
PC board may break down.

JAMMA Edge Connector (%I’ 3.96 mm pitch)
Terminal side

Soldered side
GND
GND
+5v
+5v
+lZV
Mis-insert preventive key
Cain counter 2

GND
GND

A
I3
C
D
E

F
H
J
K

d
e
f

2
3
4

Parts mounted side
GND
GND
+5v
+5v

5
6
I

+12v
Mis-insert preventive key

8
9

26
21

- 13-

Coin counter 1

GND
GND

Check the power source for the cabinet connecting to the JAMMA edge connector and voltage
of the power source for the coin counter of the cabinet.

! WARNING :

n
l

The power source on the cabinet connected to the JAMMA edge connector should fit the following
requirements:
- Voltage allowable error for +5V should be ~5% Amperage should be 2.5A or more
- Voltage allowable error for +12V should be L%, Amperage should be 2A or more
If the power source does not conform to this requirement, it may cause a fire.

m 0

Voltage of the power source for the coin counter of the cabinet should be +12V or
+5V. If higher voltage is used, PC board may malfunction.

5-3-2 Checking the Extended Edge Connector @B
To connect this product to the cabinet corresponding to the JAMMA standard, use the extended
edge connector attached to this product.
Check if the terminal numbers of the extended edge connector conform to the following table.
*

The extended edge connector shall not be used when installing the product to the cabinet
-..
corresponding to the JAMMA VIDEO standard (JVS).

m l Nothing should be connected to the blank parts of the table. Otherwise the PC
board may break down.
Extended Edge Connector (48P 2.54 mm pitch)

PI button switch 4 (blue)

Al5
A16
A17
Al8
A19
A20
A21
A22
A23
A24

B15
Bl6
817
Bl8
B19
B20
B21
B22
B23
B24
- 14-

Pl button switch 5 (purple)

5-3-3 Connecting to the Control Panel m
This product has to be connected to the control panel (see below) described in the chapter
SPECIFICATIONS” (on p.6) to use.

Pl Stan switch

PZ 8-direction
I

“2.

joystick

P2 button switches
PI button switches
Turn the power of the cabinet OFF and unplug the power cord from an electrical outlet.

Remove the control panel in accordance with the instmctions on “control panel” described in
the operation manual of your cabinet.

If the control panel of your cabinet is different from the above drawing, refer to the operation
manual of your cabinet and replace the control panel or add/reduce button switches. If some
switches are reduced, be sure to fill up the switch holes with hole caps.

- 15-

Connect the wires of the extended edge harness on the following table to the terminals of PI
button switch 4,5,6 and P2 button switch 4,5,6 on the control panel by soldering or fixing an
applicable crimp-style terminal.

Soldered side

Terminal side

P2 button switch 4 (white/blue)

Pl button switch 4 (blue)

Parts mounted side

P2 button switch 5 (white/purple)

A19

GND (black)

BIO

GND (black)

B13
B19

Pl button switch 5 (onrole)

switch 45.6

F2 b u t t o n switch 4,5,6

Extended edge harness

r &WARNING:
0 Always use the extended edge harness specified by Namco Ltd. Otherwise it may cause a fire or
electrical shock. Contact your distributor to order parts. Refer to “11. REPLACEMENTPARTS
LIST,’ on p.56 for details of the replacement parts.

m
Apply
insulating heat contraction
0
circuit.

tube

the

connecting

part

prevent short-

0 In case the button switch is three-terminal, the input terminal (wires with the
terminal number A8,A9, AZO,BS,Bl3,B19) of the extended edge harness should
be connected to the N.O. terminal of the button switch. GND of the extended
edge harness (wires with the terminal number B9, BlO) should be connected to
the COM terminal of the button switch.
In case the button switch is two-terminal, these can be connected to either
terminal.
5

Install the control panel on the cabinet.

- 16-

S-3-4 Connecting to the Speaker m
Connect the product to the speaker(s) of your cabinet in the following procedure so that the cabinet
outputs the sound.
First check whether your cabinet has one speaker (monaural) or two speakers (stereo).

One speaker (monaural)
1

Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet,

Conduct a meaSure to prevent short-circuit, for instance, wmp the edge of the unused wire (Al,
B 1) of the extended edge harness with insulating tape.

After completing all the following connection, switch to “MONAURAL” in the test mode
(Ref. “6-4 SOUND TEST’ p.37).
.

“5-2 Installing the PC Board on the Install Board of the Cabinet (p.ll)

“5-3-l Checking the JAMMA Edge Connector (p.13)

“5-3-2 Checking the Extended Edge Connector (p.14)

“5-3-3 Connecting to the Control Panel (p.15)

“5-3-5 Connecting to the Connectors (p.18)

This product is set as stereo spec. as the factory-setting. When used as stereo spec.
with the cabinet of the monaural spec., only the left speaker outputs the,sound.

0 Two speakers
1

Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Connect the wires of the terminals Al and B 1 of the extended edge harness to the right side
(R) speaker by soldering or fixing an applicable crimp-style terminal in accordance with the
following table.

electrical shock. Contact your distributor to order parts. Refer to “11. REPLACEMENT PARTS
LIST’ on p.56 for details of the replacement parts.

Terminal side

Soldered side
Speaker R (-) (yellow)

Parts mounted side
BI

- 17-

Speaker R (+) (oran&

5-3-5 Connecting to the connectors a
1

Turn OFF the power switch of the cabinet and unplug the power cord from an electrical outlet.

Connect the JAMMA edge connector attached to the cabinet and the extended edge connector
in the direction shown below so that the mis-insert preventive key would fit the notch of the
connector slot of the PC board.

m 0

Do not connect the JAMMA edge connector reverse or shifted slightly. The
cabinet and PC board may break down.

k
/

Mb-insert
preventive

- 18-

Mis-insert
preventive key

3 Put the PC board installed on the install board into the cabinet
m l Be sure to fix the install board to the cabinet. If not, it may break down due to
vibration.
l

Be careful that the PC board does not touch any harnesses or cables after being
put inside the cabinet. If it is kept operating with touching to any of them, it may
break down.

‘.

- 19-

5-4

Connecting the Product to the Cabinet Corresponding to JAMMA
VIDEO Standard (JVS) m
The explanation on connection to the cabinet corresponding to the JAMvIA VIDEO standard (JVS)
and on transfer of the data to be displayed on the Natnco-made CYBERLEAD cabinet is given here.
First, perform the procedure of “5-2 Installing the PC Board on the Install Board of the
Cabinet” (on p.11). When two cabinets are linked with cables for networked head-to-head
play, the PC board can be installed to either cabinet.

5-4-l

Connecting to the Control Panel m
This product has to be connected to the control panel (see below) described in the chapter “2.
SPECIFICATIONS” (on p.6).
E-direction
P2

Pair control
PI

joystick

button switches

panel (two persons can play in one cabinet)

&direction joystick,

Pl bUpOn2SW;ltCheS

~1 stan switch
/

4 5
PI button switches
Single control panel
(players can play networked head-to-head play by connecting two cabinets with cables)
Note: The figure above shows the control panel of the cabinet on which the PC board shall be installed.
The joystick and the switches on the control panel on the cabinet that the PC board is not installed
shall be for P-2.
Te name of each joystick and switch in the figure above corresponds to general name of the
control panel connecting terminal (attached to the cabinet) of the cabinet corresponding to
the JAMMA VIDEO (JVS) standard as follows.

-2O-

Turn the power switch of the cabinet OFF and unplug the power cord from an electrical outlet.

In cases that the control panel of your cabinet is different from the figure in the previous page,
replace the control panel or add/reduce button switches. If some switches are reduced, be sure
to fill up the switch holes with hole caps.

Check if each joystick and switch of the control pane1 is appropriately connected to each
control panel connecting terminal on the cabinet with reference to the figure in the previous
page and the operation manual of your cabinet.

Control panel connecting terminal
attached on the cabinet

m l In case the button switch is three-terminal, the input terminal (such as
IP-PUSHI) of the control panel connecting terminal should be connected to the
N.O. terminal of the button switch. GND of the control panel connecting terminal
should be connected to the COM terminal of the button switch.
In case the button switch is two-terminal, these can be connected to either
terminal.

5-4-2 Connection of Cables m

0 The power source on the cabinet connected to the power cable should fit the following requirements:
- Voltage allowable error for +5V should be ti70, Amperage should be 2SA or more
If the power source does not conform to this requirement, it may cause a fire.

Turn the power switch of the cabinet OFF and unplug the power cord from the electrical outlet.

-21-

Connect the cables of the cabinet to the corresponding connectors of the PC board as the figure
below.

l/O cable

Audio cable
* Connect the one printed “red” or “R”
fo either of the red terminals
Connect the one printed “white” or
7” to either of the white terminals
l

/
Video-cable
* Able to be connected to either terminals. If there are Iwo
video cables, connect both cables to the terminals (either).

Prevent short-circuit by wrapping insulating tapes around unnecessary connectors of the
cabinet.

Put the PC board into the cabinet.

w 0 Fix the install board on the cabinet. Otherwise, vibration may cause a breakdown.

l Be careful that the PC board does not touch any harnesses or cables after being
put inside the cabinet. If it is kept operating with touching to any of them, it may
breqk down.

5-5

Pasting the Stickers (Both for m, m)
Paste the stickers included in the package on the cabinet and install it.

Title sheet

A sticker
B sticker

Namco-made CYBERLEAD

cabinet, for example

Put together the POP referring to the attached operation manual, and place it appropriately.

-23-

6. ADJUSTMENT FOR OPERATION
The cabinet needs to be conducted adjustment for operation (setting or altering) in order to operate
SOULCALIBUR game.
The following items can be adjusted.
Item

Reference

1Check/adjustment of the display

16-2 Display Test (p.28)

Testing

switches

connected

board

6-3 Switch Test (p.34)

Testing

sound

output

setting

speakers

6-4 Sound Test (p.35)

and

-1

Setting of VIDEO SYNC on the cabinet
corresponding to JAMMA VIDEO standard (NS)

6-5 NS Cabinet Options (p.36)

Setting of the game options

6-6 Game Options (p.38)

Setting of play fees

6-7 Coin Options (p.39)

Actual play data

6-8 A.D.S. (p.42)

Clear the data

/ 6-9 Data Clear (p.42)

Use the adjustment switches on the PC board and the switches on the control panel of the cabinet to make
adjustment.
The basic knowledge of the various adjustment switches and the adjusting procedures necessary for
operation shall be explained here.

6-l The Basic Knowledge of the Adjustment
m 0 A service technician should not be charged electricity when touching the PC board.
Static electricity may cause the product breakdown or damage.

- 24 -

6-l-l

Adjustment

Switches, Knobs

The PC board has a switch and a knob for adjustment, the option switch and speaker volume.
Q Option switch
l

No.1 shall be used to switch the test mode/game mode.
ON: Test mode
OFF: Game mode

No.2 shall be not used

m 0 These should be OFF when operating the game.
0 Speaker volume (knob)
This knob adjusts the volume of the speaker sound of the cabinet.
l

Turn to right : Sound volume increases

Turn to left : Sound volume decreases
*

This speaker volume cannot adjust the sound volume for the cabinet corresponding
to the JAMMA VIDEO standard (JVS). The sound volume should be adjusted on
the cabinet.

.,
0 Option switch

-25-

6-l-2

Selecting the Adjusting Items
Display the test menu screen on the test mode to make adjustment.
1

Turn the power switch of the cabinet ON to display the game screen.

Turn No.1 option switch (0) ON.

Option switch (0) on the PC board and the slide type test switch on the cabinet can make it
enter the test mode only when they are switched from OFF to ON. They cannot make it enter
the test mode even when they are already set ON. In this case, you have to turn it OFF and
then turn it ON again.

It enters the test mode and the test menu screen appears.
*

You may perform the procedure to return to the test menu from each test under “6-2 pisplay
Test” (p.28) through “6-9 Data Clear” (p.42) to display the test menu.

------ (62)

DISPLAY TEST

Display rest

SWITCH TEST

Switch test

_.-___ (($3)

SOUND TEST

Sound tes

‘______ (6-2)

JVS cabinet option

______ (6-S)

option

_--___ (6-b)

Coin option

-----_ (6,)

Check play data

______ (6-g)

Data clear

------

JVS CABINET OPTIONS
GAME

OPTIONS

Game

COIN OPTIONS
A.D.S.
DATA

CLEAR

E X I T & SAVE

((j-9)

Finishing the test mode ------ (6-l-3)

-26-

Hit the Pl S-direction joystick up or down to turn the item to be adjusted in red referring to “62 Display Test” (p.28) through “6-9 Data Clear” (p.42).
P!

S-direction joystick

Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA
VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as P 1.
The items to he adjusted can be selected through the following list.
Adjustment
ChecWadiustment
Testing

Item to be selected

of the dismay
.
_

switches connected

1! D I S P L A Y T E S T

p.28

1S W I T C H T E S T

p.34

Testing sound output and setting speakers

SOUND

p.35

Setting of VIDEO SYNC on the cabinet
corresponding to JAMMA VIDEO standard (JVS)

J-KS CABJNET

PC board

Reference

TEST
OPTIONS

p.36

Setting of the game options

GAME

OPTIONS

p.38

Setting of play fees

COIN OPTIONS

.- p.40

Actual play data

A. D. S

p.42

Clear the data

DATA

CLEAR

p.42

Press the Pl button switch 1 to select the test screen. The test screen selected is displayed.

* “JVS CABINET OPTIOh”’ cannot be selected when the PC board is connected to the
cabinet corresponding to the JAMMA standard. It can be selected only when the PC
board is connected to the cabinet corresponding to the JAMMA VIDEO standard
WS).

Note: The above tigure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA
VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.
5

Make adjustment on the test screen selected.
The detailed adjustment procedure shall be explained under each chapter from “6-2 Display
Test” (p.28) through “69 Data Clear” (p.42).

-27-

6-l-3

Finishing the Test Mode
After making adjustment of each item according to “6-2 Display Test” (p.28) through “6-S Data
Clear” (p.42) display the test menu screen.
1

Hit the Pl S-direction joystick up or down to turn “EXIT & SAVE” in red.

Press the Pl button switch 1. The test mode finishes and it returns to the game screen.

Turn No.1 option switch (0) OFF.
* In case that tbe test switch on the cabinet is used, turn that test switch OFF.

m 0 If the test mode is not finished in the above procedure, the adjusted result (setting
or altering) may not be effective. Always finish the test mode in the above
procedure. (The test mode cannot be finished only turning the test switch OFF
without selecting “EXlT & SAVE”.)

6-2

Display Test (Check/adjustment of the display)
The following check and adjustment shall be made.
=

COLOREDIT
The shade and tone balance of the picture signal outputted by the PC board shall be checked and
adjusted.

CONVERGENCE
It is used to check/adjust the size, position, aspect ratio, distortion of the picture.

COLORBAR
It is’used to check/adjust the shade and the tone balance of the picture.

Before conducting any of the above, conduct the following “common operation”.

-28-

6-2-l Common Operation
1

Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (~28-29).
“DISPLAY TEST’ in 3.

Select

“Color Edit” screen shall be displayed over the “diagonal” screen as follows.
Color edit screen

CONVERGENCE

PREVIOUS VALUE : P-l BUTTONS
EXIT COLOR EDIT
: P-l BUlTON4
PdEp COLOR TEST ; ;I; &~~Nl

Color edit screen is displayed over the diagonal screen.

* Pressing the Pl button switch 4 switches the “color edit” screen displayed/nondisplayed.

I I II II II
ENTER COLOR EDIT : P-l BUTTON4
yC$r COLOR TEST : P-l BUlTONl
: P-l START

The color edit screen is not displayed

-29-

Press the Pl button switch I to go the other adjustment item.
*

Each time you press the switch, it shifts from “CONVERGENCE” -> “COLOR BAR”
-> “CONVERGENCE” . . . . . . and its screen is displayed each time.
Pl button switch 1

PI start switch

PI button switch 4

Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabiners corresponding to the JAMMA VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as PI.

6-2-2

According to the item to be adjusted, perform the procedure described under “6-2-2
CONVERGENCE” (p.30) through “6-Z-3 COLOR BAR” (p.32).

Press the PI start switch to return to the test menu screen after completing the whole
“DISPLAY TEST’. The test menu screen (p.26) is displayed.

Perform “6-l-3 Finishing the Test Mode” (p.2X)

to exit the test mode.

CONVERGENCE (Checking/adjusting the size, position, aspect ratio, ..
distortion of the picture)
1

Perform the procedures 1 and 2 of “6-2-l Common Operation” (p.29) to displayd the
“CONVERGENCE” screen.
*

If “DISPLAY TEST” screen appears already, common operation 1 is not needed.

m 0 If the “CONVERGENCE” screen is not displayed, keep pressing the PI button
switch 1 until it is displayed.
* Each time you press the switch, it shifts from “CONVERGENCE” ->
“COLOR BAR” -2 “CONVERGENCE” . .._.. and its screen is displayed each
time.

Pl,bunon switch 1

-3o-

On the “CONVERGENCE” screen, the following “cross hatch pattern” is displayed.

Cross hatch pattern

I I I I I
! ! ! ! ! ! ! ! ! ! I
ENTER COLOR EDIT : P-l BLiTrON4
gp COLOR TEST : P-l BlJlTONl
: P - l SIART
I I * I I I,
I I I I I

I
/$$$$I

Note: The above shows the screen with the color edit non-displayed. It makes no
difference if the color edit is displayed.
2

Press the Pl button switch 2 to
check the size, position, aspect
ratio, and distortion of the cross
hatch pattern on each color.
*

Each time you press the PI
button switch 2, the color of
the “cross hatch pattern”
changes from white -> blue ->
red -> purple -> green -> light
blue -> yellow -> black ->
white ._____ in this order.

When the size, position, aspect ratio of the pattern is not appropriate or distorted, refer to the
operation manual of the cabinet or contact the manufacturer of the cabinet to adjust it on the
cabinet.

Press the PI start switch to return to the test menu screen after completing the whole
“DISPLAY TEST’.
Press the Pl button switch 1 to display the adjusting screen for the other adjustment in the
“DISPLAY TEST’.
PI burton switch I

PI scan switch

Note: The above figure shows the pair conuol panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA
VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.
5

Perform “6-1-3 Finishing the Test Mode” (p.28) to exit the test mode.
-3l-

6-2-3

COLOR EDIT, COLOR BAR (Adjustment of the shade and tone balance of
the picture signal outputted by the PC board)
1

Perform the procedures 1 and 2 of “6-2-l Common Operation” (p.29) to display the “Color
Edit” screen over the ‘Color Bar” screen.
*

If “DISPLAY TEST” screen appears already, common operation 1 is not needed.

In the “Color Bar”, the following screen appears.
*

Each color bar of “white” “red” ‘@een” “ blue” is displayed with gradual shading. Press
the PI button switch 2 to change the shade and tone of the color from 32 -> 16 -> 8 -> 4 ->
2 -> 32 . . . . _ in this order.
PI button switch 2

COLOR BAR

Contrast : 00

Bright R :OO
Bright G : 00
Bright B : 00

whole cD”m.st
Brightness (red)
Brightness ( een)
Brightness (ITlue)

Color bar (white)
Color bar (red)
Color bar (green)
Color bar (blue)
PREVIOUS VALUE : P-l BUlTON5
EXIT COLOR EDIT : P-l BLKrON4
!+I? COLOR TEST : P-l BUlTONl
: P-l START

How to initialize the value
How to finish the color edit
How to go to the next test pattern
How to mum to the test menu screen

w l If the “COLOR BAR” screen is not displayed, keep pressing the PI button switch
1 until it is displayed.
* Each time you press the switch, it shifts from “CONVERGENCE” ->
“COLOR BAR” -> “CONVERGENCE” . . . . . . and its screen is displayed each
time.
0 If the “Color Edit” screen is not displayed, press the PI button switch 4. The
“Color Edit” screen is displayed over the “COLOR BAR” screen.
*

Press the Pl button switch 4 to switch the “Color Edit” screen displayed/nondisplayed.

-32-

Hit the PI S-direction joystick to up or down to select the adjusting item out or
“Contrast”, “Bright R”, “Bright G”, and “Bright B”.
PI button switch I
Pl S-direction joys,tick
/

’ PI bunon switch 4
Note: The above figure shows the pair control panel. In
case of the single control panel (that is, two cabinets
corresponding to the JAMMA
VIDEO standard
(JWS) are linked for networked head-tohead play),
the control panel of the cabinet on which the PC
board is installed shall be called as Pi.
3

Hit the Pl S-direction joystick to right or left to change the setting.
* The details of-the adjustment is shown in the table below. The result of the adjustment
shall he checked on the color bar on the screen.
Description

Item
)

Contrast

1 Adjusting contrast of the picture

Bright R

Adjusting shade and tone of red color of the picture signal

Bright G

Adjusting shade and tone of green color of the picture signal

Bright B

Adjusting sbade and tone of blue color of the picture signal

I
I
‘..

* After changing the setting,
* To initialize the settings,
Press the Pl button switch 5. The changed settings are erased. .
l

To stop adjusting,
press the PI button switch 4. The ‘Color Edit” screen disappears and adjustment is
suspended.
To re-adjust,
press the Pl button switch 4 again. The “Color Edit” screen appears again for re-adjustment

Press the Pl start switch to return to the test menu screen after completing the whole
“DISPLAY TEST’.
Press the PI button switch 1 to display the adjusting screen for the other adjustment in the
“DISPLAY TEST’.

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

-33-

PI. burton switch I

Pl button switch 4 71 button switch

Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA VIDEO standard (NS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.

6-3 SWITCH TEST
Use the SWITCH TEST function to test the switches connected to the PC board such as the buttons
on the control panel.
1

Perform the procedure 1 - 4 of “6-I-2 Selecting the Adjusting Items” (p.28-29).
“SWITCH TEST” in 3.

Select
..

The following screen is displayed.
PI button switches
p2 start switch

PI stan switch
PI &direction

joystick

Pl button switches
Service &itch of the cabinet
Test switch of the cabiner
Opti on switches of the PC board
The number of activation of
the coin counter (initially 0)

Notes: * The button switches not specified in the above figure shall not be used.
* Ignore displays such as [ lP] and [2P]
* The currenr status shall be displayed under “SERVICE”, ‘TEST SW”, “DIP SW
I”. “DIP SW 2”, “COIN I”, “COIN 2”. (In case that there is only one coin
counter, 0 shall be displayed under “COIN 2 ” .

-34-

Operate each joystick and switch on the control panel one by one.

The joysticks on the screen moves in accordance with the actual moves of “PI &direction
joystick” and “P2 S-direction joystick”. The button on the screen is highlighted in white
when the actual button switch on the control panel is pressed.

m 0 If the screen does not change in accordance with the operation of the joysticks and
the switches on the PC board, the game play cannot be played correctly. Refer to “8-2
TROUBLESHOOTING” (p.48) in that case.

Press the Pl button switch 4 and 5 at the same time to return to the test menu screen.

PI button switch 4
Note:

6-4

?l button switch 5

The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA
VIDEO standard (JVS) are
linked for networked head-&head play), the control panel of the cabinet on which
the PC board is installed shall be called as PI.

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

SOUND TEST (Test/setting of the sound)
Testing of the sound output of the cabinet and the setting of the speakers monaural/stereo shall be
made here.
Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27). Select
“SOUND TEST”’ in 3. Tdistributor to make inquiries about this product and/or about repair.

SOUND TEST
SOUND : [000]
STATUS : 0000

Sound number
Status of sound output

SPEAKER OUT : STEREO

SOUND PLAY
XV&MONAURAL]

: Pl -BUTTON1
: Pl -BLfl-fONZ
: Pl -START

How co play the sound

How to change the setting of monnurnllstcrro
How to return to the test men” screen

- 35 -

Make adjustment according to the description on the table below with the appropriate joystick
and the switch.
Item

Test/Adjustment

How to operate

Changing tbe sound number

The sound to be used in the
game is selected.

Hit the Pl S-direction joystick to right or left to
change the number.

Play the sound

The sound of tbe selected
number is played.

Press the PI button switch I to play the sound.

Switch monaural/stereo

Monaural sound/stereo sound is
switched.

Press the Pl button switch 2 to switch.

Stereo sound test

Stereo sound output is tested.

Select the sound number [OOI], press the Pl button
switch 1. The sound is played from the left
speaker, right speaker, and finally both speakers as
stereophonic.

m 0 If something wrong is found when checking the adjustment, refer to “g-2
TROUBLESHOOTING” on p.48.

Press the Pl start switch to return to the test menu screen.
PI buyzn sjuitches
I \ \

Pl start switch

Note: Tbe above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to tbe JAMMA
VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.
4

6-5

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

JJTS CABINET OPTIONS (Setting VIDEO SYNC on the cabinet
corresponding to the JAMMA VIDEO standard (JVS)) m
VIDEO SYNC setting for the cabinet corresponding to the JAMMA VIDEO standard (JVS) shall be
made.
*
1

When the PC board is connected to the cabinet corresponding to the JAMMA standard, this
option is not available even if it is displayed.
Perform the procedure 1 - 4 of “6-I-2 Selecting the Adjusting Items” (p.26-27). Select “JVS
CABINET OPTIONS” in 3.
The following screen is displayed.

-36-

JVS CABINET OPTIONS
<DEFAULTS IN GREEN>
--f VIDEO SYNC: Composite

JAMMA VIDEO STANDARD
[STEP 11
Main : . . . . . . . . . . . . . . . . .

,,*,:.

. . . . . . . . . . . . . . . .

j/o 2: .

. . . . . . . . . . . . . . . .

EXIT
2

: Pl -START

Display on the JAMMA
srandard (IX)

VIDEO

Hit the Pi S-direction joystick to right.
Each time it is hit, the synchronizing signal output type of the video output, which is displayed
under “VIDEO SYNC” (shown as (a) in the above figure), shall be switched to change the
setting. (The type shown in the thick frame below is the default setting.)
PI 8-direction

joystick

Synchronizing signal output type of the video output
Composite

(composite

synchronization)

Separate

(vertical synchmnizationfnorizonral

synchronization)

m l When using the cabinet corresponding to the separate signal, set the ‘VIDEO
SYNC” as “Separate” for the best picture.
l Namco-made CYBERLEAD cabinet corresponds to the separate signal. But if
another monitor display is connected to the line output picture terminal on the back
of the cabinet, set the “VIDEO SYNC” as “Composite”, because that monitor
display may get poor picture under the “Separate” setting.
3

Press the PI start switch to return to the test menu screen.
PI start switch

6-6

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

GAME OPTIONS (Setting of the game options)
Game options such as the game difficulties shall be set here.
1

Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27).
“GAME OPTIONS” in 3.

Select

The following screen is displayed.
GAME OPTIONS
<DEFAULTS IN GREEN>
DIFFICULTY LEVEL : MEDIUM
FIGHT COUNT<1 P GAME> : 1
FIGHT COUNT<VS GAME> : 1
LIFE BAR<1 P GAME> : +l
UFE BAR&S GAME> : +1
ROUND TIME : 99
GUARD DAMAGE : OFF
GUARD DAMAGE : ON
CHARACTER CHANGE AT CONTINUE : YES
CHARACTER CHANGE AT VS GAME : NO
MUSIC IN A-iTRACT : YES
EVENT MODE : OFF
4 PLAYERS MODE : OFF
HIT COLOR : RED
EXIT
: Pl -START
2

Hit the PI S-direction joystick up
or down to select an item to
change the setting out of (a) - (i)
on the above figure. The selected
item is highlighted in red.

/
3

Hit the Pl S-direction joystick right or left to change the setting.
The details of the setting of each item are as follows. (The default setting out of factory is
shown by the thick frame here.)
( a) DIFFICULn

LEVEL(Difticulty

EASY

MEDIUM

of the game play)
HARD

VERY HARD

ULTRA HARD

( b ) FIGHT COUNT< 1P CAME>(Tbe number of rounds to be cleared to win in IP play mode)
I

(c ) FIGHT COUNT<VS GAMEj(Tbe number of rounds to be cleared to win in 2P play mode)
I

-38-

( d ) LIFE BAR<lP GAME>(Life gauge in 1P play game)
NORMAL

-1

-2

( e ) LIFE BAR<VS GAME>(Life gauge in 2P play game)
-2

1 NORMAL

-I

( f )ROUND TJME(Time

per 1 round[second])

( g )GUARD DAMAGE@amage at guard)
ON(a little)
I

OFP(none)

(h )NEUTRAL GUARD(Guard in the condition that the lever is not be tilted)
ON(exist)

OFF(none)

( i) CHARACTER CHANGE AT CONTINUE(Changing
YEXpossible)

I
(j )CHAR4CIER
I

CHANGE AT VS GAME(Changing characters in 2P play when somebody buys-in)
YES(possible)

( k ) MUSIC IN ATTRACT(Sound
I

characters at a continued play)
NO(impossible)

yEs(possible)

NO(impossible)

played in attract mode)

NO(impossible)

( 1) EVENT MODE[Management after the 2P play is finished)
ON(both of them:game over)
FF(winnercontinue
1Pplay game)

( m ) 4 PLAYERS MODE(4 players control *need 2 JVS cabinets)
Om=(Z playen)
ON(4 players)
( n ) HIT COLOR(Red display effect at hit)
GWN(changed
RED(exist)
I

to another color)

Press the Pl start switch to return to the test menu screen.

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

- 39 -

6-7

COIN OPTIONS (Setting of play fees)
Coin options such as the credit needed to play one game play shall be set here.
1

Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27).
“COIN OPTIONS” in 3.

Select

The following screen is displayed.

COIN OPTIONS
<DEFAULTS IN GREEN>

(4
(b)
(c)
Cd)
(4
(f)
(9)

VALUE:
VALUE:

: Pl -SART

EXIT

Hit the Pl S-direction joystick up or down to select an item to change the setting out of(a) - (g)
on the above figure. The selected item is highlighted in red.

w l Before changing the settings of (a) - (0, be sure to set OFF (g) “FREE PLAY”.
The settings of (a) - (f) cannot be changed if(g) is set ON.

Hit the PI S-direction joystick right or left to change the setting.
S-direction joystick

Pl.

Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as PI.
The details of the setting of each item are as follows. (The default setting out of factory is
shown by the thick frame here.)
(a)

START COST (The number of coin(s) needed to play an initial game play)
2

(b)

COIN(S) TO START

CONTINUE COST (the number of coin(s) needed to play a continued play)
I

COIN(S) TO CONTINUE

Note: This value should be the same value as (a)START COST or smaller.

-4o-

(c)

COIN CHUTE I MECHANICAL VALUE
(The number of coin(s) to be added when the coin switch 1 activates once)
1

(d)

COINCOUNTAS

1
(e)

9 I COIN

COIN CHUTE 2 MECHANICAL VALUE
(The number of coin(s) to be added when the coin switch 2 activates once)
COINCOUNTAS

COIN

CREDlT MODE (Record of credit)
COMMON

EACH ONE

(When either coin switch activates, or either
stan switch is pressed, these are counted on
one common credit.)

(Pl side and P2 side have own credit system;
Pl side corresponds to the coin switch 1 and
P2 side corresponds to the coin switch 2.)

* When the cabinet which allocates a pair of coin switch and coin counter for each PI and
P2 side is used, the coins counted for Pl and P2 side can be recorded separately by
setting (e) CREDIT MODE as “EACH ONE” and (f) COIN COUNTER as “2
couNTERY.
Notes:

m 0

(f)

The cabinet corresponding to the JAMMA VIDEO standard (JVS) with one
coin counter is fixed to set “COMMON” only and cannot be changed to “EACH
ONE”.
When two cabinets corresponding to the JAMMA VIDEO standard (JVS) are
linked to set networked play, it is fixed to set “EACH ONE” onlf and cannot be
changed to “COMMON”.
When setting the CREDIT MODE as “EACH ONE”, make sure that the PC
board and the coin switch 2 on the cabinet is connected. Otherwise P2 side
cannot accept coins nor play a game.

COIN COUNTER (Allocation of the coin counter)
1 COUNTER

Notes:

(g)

(Two coin switches uses one coin counter in
common.)

2 COUNTERS

(Each of two coin switches uses own coin
I counter.)

The cabinet corresponding to the JAMMA VIDEO standard (JVS) with one
coin counter is fixed to set “1 COUNTER” and cannot be changed to “2
COUNTERS”.
When two cabinets corresponding to tlie JAMMA VIDEO standard (JVS) are
linked to set networked play, it is fixed to set “2 COUNTERS” and cannot be
changed to “1 COUNTER”.

FREE PLAY (Setting of free play)
YES (coins needed)

-41-

NO (no coins)

Press the Pl start switch to remm to the test menu screen.
PI, SLUL switch

Note: The above figure shows the pair control panel. In case of the single control panel
(that is. two cabinets corresponding to the JAMMA VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of rhe cabinet on which
t&nll Iw-. Cn.lrrl
L.~‘-*l.y~sh~,&.e-ca!~&
a p;.
.L
UYUY ;rAJ LIIJul‘lL.
5

6-8

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

A.D.S. (Checking the data on playing results in the past)
The data on playing results in the past such as the total playing time can be checked here.
1

Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27). Select
“A.D.S.” in 3.

Press the Pl start switch to return to the test menu screen.

Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets correspondin to the JAMMA VIDEO standard (NS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as PI.
3

6-9

Perform “6-l-3 Finishing the Test Mode” (p.28) to exit the test mode.

D&TA CLEAR (Clearing various data, initializing to default settings)
The data saved even after the power is turned off can be erased or initialized to the default value as
factory-setting. This “DATA CLEAR” function is used to emse the data or initialize it.
1

Perform the procedure 1 - 4 of “6-l-2 Selecting the Adjusting Items” (p.26-27). Select
“DATA CLEAR” in 3.

-42-

The following screen is displayed.
DATA CLEAR

(4
(b)
(cl
(dl
Cd

CANCEL

Return to the rest menu screen

A.D.S CLEAR

Clear the playing data only

RANKING CLEAR

Initialize the ranking daw

SET DEFAULTS ALL OPTIONS

Set the value

ALL CLEAR

Clear all the data recorded

of illI the options

to default

EXEC : Pl -BUl-i-ON1
EXIT : Pl -START
2

Hit the Pl 8-direction joystick up or down to select an item to erase or initialize the data out of
(b) - (e) on the above figure. The selected item is highlighted in red.
PI 8-direction
I

joystick
..

Note: The above figure shows the pair contxol panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA
VIDEO standard (JVS) are
linked for networked head-to-head play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.
what to be executed

(1)

Erase onlv the A.D.S. data (Ref. “6-8

(2)

Initialize the ranking data. such as straight victories record, to
default value as factor+setting.

A.D.S.” on p.42)

(3) ’ Initialize the values of all the options set in the test mode
(Ref. “6-2 DISPLAY TEST’ on p.28 through “6-8 A.D.S.”
on p.42) to default values as factory-setting.
(41

Execute all the (1) f2) and (3) toaetber at the same time.

-43-

Item displayed on the screen
A.D.S.
RANKING

CLEAR
CLEAR
I

SET DEFAULTS ALL OPTIONS

ALL CLEAR

Press the Pl button switch 1 to execute the selected item.
Pl button switch I

(Qi?&Me 8&&$&a
Note: The above figure shows the pair control panel. In case of the single control panel
(that is, two cabinets corresponding to the JAMMA VIDEO standard (JVS) are
linked for networked head-to-head-play), the control panel of the cabinet on which
the PC board is installed shall be called as Pl.
4

Do either one of the following procedure to return to the test menu screen.
l

Press the PI start switch.
Hit the Pl S-direction joystick up or down to select “CANCEL” on the screen and then press
the Pl button switch 1.
PI B-direction joystick

PI stan switch

Perform “6-1-3 Finishing the Test Mode” (p.28) to exit the test mode.

-44-

‘.

7. OPERATION

! WARNING :

If you have to touch the PC board during operation, refer to “8. INSPECTION & CLEANING,
TROUBLESHOOTING” on p.47.

0 Make sure that installing and connecting were conducted in accordance with the instructions and the
procedure specified in this operation manual (Ref. “5. Installing and Connecting” on p.9) before
operation. Otherwise it may cause a fire, electrical shock or machine trouble.

7-1

Persons Not Recommended to Play

IA
! CAUT’oN:l

To ensure the safety of players, those who

l
l
l

are not feeling well;
am injured on the arms or hands;
are under the influence of alcohol;

‘..

are not recommended to play this game.

7-2 Restrictions When Operated

I
! W A R N I N G :A
l

This product is designed for indoor use only. Do not operate this product outdoors. It may cause a
, fire or electrical shock.

Observe the restrictions described under “2. SPECIFICATIONS” on p.6. Otherwise it may
cause breakdown or malfunction.

0 Do not operate this product in areas:
with direct water contact:
with high humidity;
with much dust;
near heating systems;
where a drastic change in temperatune might cause dew condensation;
subject to vibration;
near inflammable or volatile substance;
near strong magnetism or radio source.
It may cause breakdown or malfunction.

-45-

7-3 How to Play
How to play the game and various techniques to be used are printed on A sticker. B sticker, and the
title sheet.

-46-

8. INSP~ON&- G,TROUB~~G
- To be serviced by a quaiified service technician only -

8-l Inspection & Cleaning
I
0 Unplug the power cord of the cabinet from an electrical outlet before conducting inspection or
cleaning. Otherwise an electrical shock may happen.
l

Do not conduct any works with wet hands. It may cause an electrical shock.

Be sure to conduct a regular inspection and cleaning according to the following table so that the
“SOULCALIBUR” game is played in good condition.
T i e

Every month
E
‘Z
8
5
.E
i
B
d

Description

Reference

Check that the PC board is fixed and connected
firmly. It might loosen due to the vibration
during the game play, and the operation in such
conditions may cause breakdown or malfunction,
_____________.__________________________------~---Check that the cabinet, harness, cables do not
touch the PC board. If operated with such contact
conditions, it may cause breakdown or
malfunction.

“5. INSTALLING
AND CONNBCTING”
(P.9)

To be serviced
by a qualified
service
technician only.
________________________________________-.
“5. INSTALLING
To be serviced
AND CONNECT’lNG~,
by a qualified
service
(P.9)
technician only.

Test the display, switches, and sound.

“6-2 DISPLAY TEST”
(P.28)
‘S-3 SWITCH TEST
(P.341
“6-4 SOUND TEST
(P.35)
----._________________
To be serviced
by a qualified
service
technician only.

Every six months
Clean the PC hard. A foreign substance or dust
on the PC board may cause breakdown or
malfunction.

Notes

m l A service technician should not be charged electricity when touching the PC board.
Static electricity may cause the product breakdown or damage.
l Clean the product using a static-electricity-free cleaning equipment such as a brush
for an OA equipment. The IC on the PC board may be damaged by static
electricity and will not function correctly.
0 Do not clean the product using the liquid such as water or detergent. Otherwise it
may cause the product breakdown or damage.
0 Do not attempt to perform conductivity test using a multi-meter. The IC of the PC
board may be damaged even by the internal voltage of a multi-meter, and may not
function correctly.
l Do not replace the built-in batteries. Otherwise breakdown or damage of the
product may happen.

-47-

8-2 Troubleshooting

! WARNING :

Always unplug the power cord of the cabinet from an electrical outlet before checking this product is
installed and connected on the cabinet correctly. Otherwise an electrical shock may occur.

m l Do not replace the built-in batteries. Otherwise breakdown or damage of the
product may happen.

When this product does not operate correctly or has any trouble, check it in the following procedure.
1

Turn OFF the power switch of the cabinet, and unplug the power cord from an electrical outlet.

Remove any foreign substance or dust on the PC board.

m
A
service0 technician should not be charged electricity when touching
Static electricity may cause the product breakdown or damage.

the

board.

l Clean the product using a static-electricity-free cleaning equipment such as a brush
for an OA equipment. The IC on the PC board may be damaged by static
electricity and will not function correctly.

Check again that this product is installed and connected correctly to the cabinet. (Refer to the
operation manual of the cabinet and “5. INSTALLING AND CONNECTING” (p.9 - 23) on this
operation manual.)

m 0 Do not attempt to perform conductivity test using a multi-meter. The IC of the PC
board may be damaged even by the internal voltage of a multi-meter, and may not
function correctly.

Plug the power cord into an electrical outlet, and turn ON the power switch of the cabinet.

Check again that adjustment is made correctly.
(Refer to “6. ADJUSTMENT FOR OPERATION” (~24 - 44) on this manual.

-48-

When the trouble is not solved even after performing the procedure from 1 through 5, turn the
power OFF, unplug the power cord from an electrical outlet, and contact your distributor.

-49-

9. Disassembling, Safekeeping, Transportation
9-l

Disassembling -To be serviced by a qualified service technician only -

! WARNING:

0 Be sure to unplug the power cord from the electrical outlet before conducting any works. Otherwise it
may cause an electrical shock.
m l A service technician should not be charged electricity when touching the PC board.
Static electricity may cause the product breakdown or damage.

Disassemble the PC board following the procedure below.
Prepare the operation manual of the cabinet at hand.
1

Turn

Open the door of the storage of the PC board in accordance with the operation manual of the
cabinet and take out the install board on which the PC board is installed.

the power of the cabinet OFF and unplug the power cord from an electric outlet.

- 50-

DisconneCt the cables and harnesses connecting to the PC board.

JAMM.\

standard cabinet, for example

Remove the screws on the four comers of the PC board and disassemble the PC board from the
install board.

Put back the install board and close the door.

9-2 SAFEKEEPING
Data not available at time of publication.

9-3

TRANSPORTATION
Data not available at time of publication

-52-

10. DISPOSAL

! WARNING :

0 Do not throw this product into a fire. Otherwise it may cause an explosion of lithium batteries used in
the product and cause injury.
0 When disposing this product, collect, transport and scrap it in accordance with law and orders.
0 If entrusting others to collect, transport and scrap this product, hire specialists in each of such work.

-53-

11. APPENDIX A
-

Control Panel Layout Template

Electrical

Diagram

-54-

NOTES:
1. DEBLIAR AND BREAK ALL SHARP EDGES
2. USE MINIMUM BEND PAD11
3. MATERIAL: 16 GA (0.06 THK) CRS
4. FINISH: C ARBIDE BLACK (SHERWIN WILLIM(S
POWN-T
5. STAMP PART NUMBER AND REV LE”EL IN 1 8” HIGH
“SING INDELIBLE INK IN APPROXIMATE POSIc ON SHOWN
6. PEMSTUD FVNGE TO BE FLUSH WITH PANEL SURFACE

EQUAL

2-R. “5-7,

;;kMNT&REE AREA

Z-R.765

_____ -__

5.421
4.062
3.653
2.353
0.000
0.990
1.99

I
2-R1.235

01.12 (REF)

DETAIL A
2

PLACES

U LlmlJ

Ll IJVzxB

San Jose, California 95131

‘ANEL CONTROL
TEKKEN TAG

TKl O - R E F E R E N C E 7
ILIINAm
xsz~ey.~e

SEEET

1 OF 1

00 ‘ti
OG’Z

00 ‘0
66.0
6’1

‘=
3

Download PDF